Born2hack

HOW TO INSTALL WINDOW 7 FROM USB DRIVE

Installing Windows from a USB flash drive has several advantages – First of all, the overall speed of the installation process will increase significantly, carrying a USB stick is much more convenient than a DVD, and finally it becomes possible to install the OS even on those systems that do not have a DVD drive, such as a netbook.
In this post, I will show you how to load the Windows installation on to your USB flash drive and make it bootable just like the DVD.
Tools Required:
1. USB flash drive with a minimum capacity of 4 GB.
2. Windows 7 set-up DVD.

Step-1: Plug-in your USB flash drive and backup all the existing data in it.

Step-2: Open the command prompt. If you are using Windows 7/Vista then open it with administrator rights*.
* Goto Start -> All Programs -> Accessories -> Right-click on “Command Prompt” and select “Run as Administrator”.

Step 3: In the command prompt, type in the following command:
DISKPART

This will start the Microsoft DiskPart utility as shown below:

Now issue the following command:
LIST DISK

This will show you a list of available disks on your system. Disk 0 is usually the hard disk. In my case, Disk 5 is the USB drive (this can be a different one in your case). Now issue the command as shown below:
SELECT DISK 5

NOTE: In the above command, 5 is the USB drive number on my system. If you have a different number on your system, then you need to replace 5 with that number.

Step-4: Now issue the following list of commands one by one as shown below:
CLEAN

CREATE PARTITION PRIMARY

SELECT PARTITION 1

ACTIVE

FORMAT FS=NTFS QUICK

ASSIGN

EXIT

Minimize the command prompt and proceed to the next step.

Step 5: Insert the Windows 7/Vista installation disc and note down the “drive letter” of your DVD drive. In my case, it is “H:”. Now type the following list of commands as shown below:

H: CD BOOT

CD BOOT

BOOTSECT.EXE /NT60 M:(NOTE: M: is your USB drive letter)

EXIT

Step-6: Copy the contents of your Windows 7/Vista installation disk into the USB flash drive.
That’s it! Your USB stick is now ready to boot and install the OS for you. Don’t forget to enable the “USB Boot” option and change the “boot priority to USB device from hard disk” in your BIOS settings.

How To Make Your Own Radio Station

Must HAVE Winamp (Any Version)
First, things First your speed has to be at least 256/64 kbps (which means Dial-up users, will have alot of latency, just dnt bother)
Second, your going to have to have a domain, an updated one with the current i.p active. (Could be anything e.g. My sig)

Now, Your gonna have to download the Shoutcast Files.

Go to www.shoutcast.com to get the files.

Ok After downloading these, installing Both of them in any order i dnt care. Go to START>PROGRAM FILES>SHOUTcast DNAS>EDIT SHOUTCAST DNS CONFIG.

Ok your gonna have to Configure it:
Go Down and where it says password: change (that means your gonna have to change it to whatever, make sure u remember)
The Portbase: change it to whatever port you want it
Maxusers: (lets be realistic here, dnt put in 10000, like NXS's radio station) your bandwidth has to be extremely good, if your cable, 50 user max is ok, ADSL should stay below 10 users, and T1 connections should do whatever tickles there fantasy.

Open winamp, RIGHT CLICK>OPTIONS>PREFRENCES>DSP EFFECT> and choose the NULLSOFT SHOUTCAST.

Go to OUTPUT, and then click on Connection, Through the ADDRESS, type your address which you have done through www.no-ip.com, PORT NUMBER, whatever u did in the EDIT.txt, and your password.

Then go to Encoder, and choose your quality of your music. Go back to OUTPU>OUTPUT CONFIG> YELLOW PAGES. this is your advertisement information. now whatever u like there

Now Connect. to check that your Radio os on-line go to http://(your address that you added in the preference)

Free Internet Radio - SHOUTcast Radio - Listen to Free Online Radio Stations Internet Radio service that offers thousands of free MP3 and AAC radio stations from radio stations and broadcasters around the world. Or use the API to build SHOUTcast Apps.

Clicking and holding an icon and then dragging it around will allow you to reorder it on the launcher. You can also drag it off to the right of the launcher to move it around. Note that you need to make an explicit movement to the right to move the icon off the launcher before you can move it around.
Dragging and Dropping an icon into the trash can will remove it from the Launcher.
Moving and holding the cursor on the left side for a few seconds will launch Unity dock.
Moving the cursor to top-left corner(near Ubuntu icon) will launch Unity dock as well.
Scrolling the mouse wheel while over the Launcher scrolls the icons if you have too many and need to move around quickly.
By Scrolling the mouse wheel while over the Sound icon on top panel helps you increase or decrease system volume.
Middle click on an application’s launcher icon – Open a new instance of the application in a new window. Very useful at times. In laptops with touchpads, hitting left/right click buttons together is akin to middle click.
Maximizing – Dragging a window to the top panel will maximize it.
Restore/Unmaximize – Dragging the top panel down OR double clicking on the top panel will do.
Tiling – Dragging a Window to the left/right border will auto tile it to that side of the screen. One of the highlights of new Unity experience

Facebook has announced two factor authentication

Facebook is the main target of hackers and spammers these days. SO facebook security team always try to make it as secure as possible. In this way they have added many security features in the website. Now facebook security team has announce some safety and security changes which include two factor authentication system and improvements to it’s Https supports.
In this multi-factor authentication systems, it has combined traditional passwords login system with additional identification methods, like one time use codes or digital keys.
This type of authentication system is also used in banking sectors for customer account protection and also announced in Google accounts earlier this year which send a code to user via sms.
In facebook the one time use code can be recieved via SMS or via VoIP call service. But for using this feature, you will have to turn this feature on for your account.f you turn this new feature on, facebook will ask you to enter a code anytime you try to log into Facebook from a new device.
In addition to two-factor authentication, Facebook also improved its HTTPS implementation, which due to the large amount of external content loaded into the website, was kind of impractical for users.